The XTR Elite Hunter Jacket is the go to jacket for the most extreme conditions. It was built with open-tops, snow storms and sever rain in mind. The Elite Hunter is perfectly suited to hunting Bull Tahr on the rugged tops of the Southern Alps as well as withstanding the intense rain during the West Coast Roar.
Although it offers the same highest-level waterproof and breathability rating as the other XTR garments, the difference lies in the extremely durable outer layer. The Extreme Hunter is the toughest Jacket in the XTR range but isn’t quite as quiet as the others in thick bush. However, after a day of constant downpour, one shake of the Jacket back at the hut, and it’s dry.
The Elite Hunter has been developed using the most advanced technology to improve not only its packability and weight, but most importantly the quality of the waterproof membrane.
It combines a great level of durability and puncture resistance with unmatched protection against the elements. When a jacket’s seams are sewn, puncture holes are created from the sewing machine, these puncture holes create potential leak points within the fabric’s membrane. With the Elite hunter we have used Welded Seams, meaning no puncture holes, lighter construction and higher durability.
Because there is no stitching to the body of the jacket the Elite Hunter is not only 15% lighter than a traditional stitched-seam jacket, but also 30% less bulky.
If you are looking for a jacket that is durable enough to handle the rigors of alpine hunting and higher resistance against the prickly alpine plants, then the Elite Hunter was built for you!
Hydrafuse ToughHD is a new generation of high performance waterproof and breathable fabric developed for hunting in extreme conditions where ultimate durability is essential.Hydrostatic pressure 30,000mm breathability 15,000gm m2 24hrs
Comments will be approved before showing up.
Place the tape measure around the large part of your chest, usually just below the arm pits. Don't stretch the tape too tight. Align this measurement with the table below to help select your size.
|CHEST CM||CHEST INCHES|
WAIST: Place the tape measure around your waist, just above where your trousers would normally naturally rest. Don't pull the tape tight, but make sure it is snug. Align this measurement with the table below to help select your size.
INSEAM: This is the measurement from the center of the crotch on our trousers, to the base of the inner leg.
|WAIST CM||WAIST INCHES||INSEAM CM|
OUTER LAYER TROUSER SIZE
Our outer layer trousers are designed to be worn over the top of your regular trousers. The sizing is therefore larger than our regular trousers. Below are the dimensions of the outer layer trousers.
|WAIST CM||WAIST INCHES||INSEAM CM|
WOMEN'S SIZE (CM / INCH)
This is the measurements of the person, not the garments.
|8||84cm / 33"||74cm / 29.1"||106cm / 41.7"|
|10||89cm / 35"||78cm / 30.7"||110cm / 43.3"|
|12||94cm / 37"||82cm / 32.3"||114cm / 44.9"|
|14||99cm / 39"||86cm / 33.9"||118cm / 46.4"|
|16||104cm / 41"||90cm / 35.4"||122cm / 48"|
|18||109cm / 43"||94cm / 37"||126cm / 49.6"|
|20||114cm / 45"||98cm / 38.6"||
130cm / 51.2"
All sizes are US men's sizing. Measure from the from the back of your heel to the end of your longest toe.
|US||FOOT LENGTH (approximate)|
|7||9.6 in / 24.4 cm|
|8||9.9 in / 25.2 cm|
|9||10.25 in / 26 cm|
|10||10.6 in / 26.8 cm|
|11||10.9 in / 27.8 cm|
|12||11.25 in / 28.6 cm|
|13||11.6 in / 29.4 cm|
Measure the circumference of calves at the thickest point. The size on the chart is the largest measurement that will fit in the gaiter. Gaiters can be tightened, but cannot be stretched to fit legs larger than the measurements shown on the chart.
|LENGTH CM||WIDTH CM|